![]() I attached my defconfig, which is working fine with 4.9-2.3. I believe that there will be something I need to enable in my kernel config, but not sure what.ĭoes anybody have any idea what’s wrong? I would appreciate any help with this problem. This was just few errors, every modules which system try to load shows this kind of error. industrialio: section 21 reloc 0 sym '': relocation 42 out of range (0x7f014664 -> 0xc0bf7cb0) soundcore: section 16 reloc 0 sym '': relocation 42 out of range (0x7f02204c -> 0xc087d0ec) Linux kernel release 5.x < The kernel’s command-line parameters. The Linux kernel user’s and administrator’s guide. caam: section 18 reloc 0 sym '': relocation 42 out of range (0x7f01c304 -> 0xc0a16908) The following manuals are written for users of the kernel those who are trying to get it to work optimally on a given system. industrialio: section 21 reloc 0 sym '': relocation 42 out of range (0x7f007664 -> 0xc0c0acb0) Update to upstream stable kernel release 5.10.I just tried the 5.0.y kernel branch and I’m having problems with modules, I’m using the same def config as for 4.9-2.3.x-imx, but something probably changed in 5.0 kernel and I’m getting these errors while loading the modules:.One important thing to consider is the life cycle of a kernel version if the version you are currently using is approaching its end of life, no more bug fixes will be provided after that date. ![]() Enable USB kernel configuration options for interacting with an Arduino over USB This new Kernel 5.0 version is a long-term release and will be supported for 6 years, earlier all Linux Kernel versions were supported for 2 years only.Refresh dxgkrnl driver to pick up bug fixes and code cleanups.Enable paravirtualized spinlock support for x86_64.Enable vPCI support under Hyper-V for arm64.Enable virtio-pmem with support for PCI BAR-relative addresses.Update to upstream stable kernel release 5.10.60.Fix Dxgkrnl build failure with GCC versions older than 8.1 (microsoft/WSL#7558).Enable the Buffer Sharing and Sync File Frameworks (CONFIG_DMA_SHARED_BUFFER, CONFIG_SYNC_FILE) for Dxgkrnl usage.Enable BPF Type Format (CONFIG_DEBUG_INFO_BTF) for use by eBPF tools (microsoft/WSL#7437).Update to upstream stable kernel release 5.10.74.Enable options related to device-mapper RAID The updated 5.0.y git tree can be found at: git:///pub/scm/linux/kernel/git/stable/linux-stable.git linux-5.0.y and can be browsed at the normal git web browser: thanks, greg k-h - Makefile 2 arch/mips/include/asm/jumplabel.h 8 - arch/mips.Unify the kernel configurations by enabling missing options on arm64.Update to upstream stable kernel release 5.10.81.Fixed SPDX-License-Identifier for d3dkmthk.h.Properly flush the device for termination during process cleanup.Removed the limit of existing and total sysmem allocations.Fix README.md build instructions to include dwarves dependency for pahole.Enable CH341 and CP210X USB Serial drivers.Update to upstream stable kernel release 5.10.93.Flush device for termination when process is destroyed to avoid a deadlock when the guest process is killed.Implement wait for sync VM bus messages as “killable” to allow killing a process waiting for a synchronous call to the host.Fix out of bounds array access for ioctls.It can be re-enabled by setting the kernel.unprivileged_bpf_disabled sysctl to 0.Update to upstream stable kernel release 5.10.102.Disable support for the Ceph Distributed File System.Linus Torvalds explains that: The numbering change is not indicative of anything special. But don’t expect grand changes just because there’s a natty new version number. Enable the Miscellaneous Control Group (CGroup) Previously earmarked to be version 4.21, the new release comes with a bucket full of improvements (as you’d expect). ![]() To find out the version of your kernel, run uname -r: uname -r If you see anything at all after the dash, you are running a distribution kernel. ![]() Enable the Landlock Linux Security Module (LSM) Unless you downloaded, compiled and installed your own version of kernel from, you are running a distribution kernel.Enable support for the Precision Time Protocol (PTP) clock device.Fix 9p filesystem regressions since the last v5.10 WSL2 kernel.Enable Retbleed mitigations in x86_64 builds This site is operated by the Linux Kernel Organization, Inc., a 501(c)3 nonprofit corporation, with support from the following sponsors.Update to stable kernel version v5.15.57.Initial release of the WSL2 kernel based on the v5.15 kernel series.Similarly, if you are running kernel version 5.0.2 and want to jump to 5.0.3, you must first reverse the 5.0.2 patch (that is, patch -R) before applying the 5.0.3 patch. This Linux kernel is delivered to your machine via Microsoft Update, and follows a separate release schedule to the Windows Subsystem for Linux which is delivered as part of the Windows image. ğor example, if your base kernel is 5.0 and you want to apply the 5.0.3 patch, you must not first apply the 5.0.1 and 5.0.2 patches. This Linux kernel is open source, with its source code available at the WSL2-Linux-Kernel repository. We've added support for WSL 2 distributions, which use a full Linux kernel. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |